COMAT 2026 - Předběžný program

13:30 - 15:30

P1

BÍLEK Vojtěch

University of West Bohemia in Pilsen, Pilsen, Czech Republic, EU

Preparation and Characterization of Mg-Based Metal Hydride Composites for Hydrogen Storage by Accumulative Fold Forging - POSTER

13:30 - 15:30

P2

BODNÁROVÁ Júlia

Czech Technical University in Prague, Prague, Czech Republic, EU

Actuated Soft Sensor for Continuous Monitoring of Tissue Mechanics - POSTER

13:30 - 15:30

P3

BRICÍN David

Research Centre Řež, Husinec Řež, Czech Republic, EU

Application of Ultrasonic Nanocrystalline Surface Modification to Austenitic Stainless Steel - POSTER

13:30 - 15:30

P4

COJOCARU Vasile Danut

National University of Science and Technology POLITEHNICA Bucharest, Bucharest, Romania, EU

Microstructure and Mechanical Properties Evolution During Thermomechanical Processing of Incoloy 925 Alloy - POSTER

13:30 - 15:30

P5

DLOUHÁ Žaneta

University of West Bohemia in Pilsen, Pilsen, Czech Republic, EU

Enhancing the Abrasion Resistance of Carbon Fiber Reinforced PEEK via WC10Co4Cr Thermal Spray Coatings - POSTER

13:30 - 15:30

P6

DRÁTOVSKÁ Veronika

Czech Technical University in Prague, Prague, Czech Republic, EU

Parametric FEM-Based Optimization of Structural Geometry for Displacement Amplification - POSTER

13:30 - 15:30

P7

DURDA Ewa

AGH University of Krakow, Faculty of Materials Science and Ceramics, Department of Physical Chemistry and Modelling, Al. A. Mickiewicza 30, 30-059 Krakow, Poland, Kraków, Poland, EU

High-Entropy Spinel-Based Ceramic/Metallic Layered Systems for SOFC Interconnect Protection - POSTER

13:30 - 15:30

P8

FOUSEK Jakub

COMTES FHT a.s., Pilsen, Czech Republic, EU

Mechanical and Microstructural Evaluation of Potentially Biodegradable Iron-based Alloys for Temporary Bone Implants - POSTER

13:30 - 15:30

P9

HSIEH Bing-Ru

National Sun Yat-sen University, Kaohsiung, Taiwan

Mechanical Properties and Microstructure Evolution of Copper-Manganese-Tin Alloy Using Selective Laser Melting and Development of Bimetallic Printed Alloys - POSTER

13:30 - 15:30

P10

Hsin Tzu Wang

National Sun Yat-sen University, Kaohsiung, Taiwan

Microstructural and Property Optimization of Rolled Low-Thermal-Expansion FeNi Alloys by Annealing and Minor Alloying - POSTER

13:30 - 15:30

P11

JÁNSKÁ Danuše

COMTES FHT a.s., Dobřany, Czech Republic, EU

Extending the Service Life of Forming Tools Using DED Technology: Development and Industrial Validation - POSTER

13:30 - 15:30

P12

KLAMCZYŃSKI Kamil

Kielce University of Technology, Kielce, Poland, EU

The Effect of Active Pneumatic Vibration Damping in a Lathe Tool Holder on the Stability of the S355 Steel Turning Process - POSTER

13:30 - 15:30

P13

KONOPÍK Pavel

COMTES FHT a.s, Dobřany, Czech Republic, EU

Extension of Miniature Testing Methodology to Hydrogen Environment - POSTER

13:30 - 15:30

P14

KOUKOLÍKOVÁ Martina

COMTES FHT a.s., Dobřany, Czech Republic, EU

Application of Additive Manufacturing for Advanced Nuclear Reactor Components - POSTER

13:30 - 15:30

P15

KOUT Jan

COMTES FHT a.s., Dobřany, Czech Republic, EU

Effect of Laser Energy Density on Structural Integrity and Mechanical Properties of Directed Energy Deposited High Entropy CoCrFeMnNi Alloy - POSTER

13:30 - 15:30

P16

KROTÁK Stanislav

SGB-SMIT GmbH, Olomouc, Czech Republic, EU

FEM‑Based Structural Assessment of Transformer Protection Enclosures under Wind and Snow Loads - POSTER

13:30 - 15:30

P17

KUBÁŠOVÁ Kristýna

Czech Technical University in Prague, Prague, Czech Republic, EU

Nitinol in Orthopedics: Mechanical Properties and Clinical Potential - POSTER

13:30 - 15:30

P18

MARUŠÁKOVÁ Daniela

Research Centre Řež, Husinec-Řež, Czech Republic, EU

Corrosion of 310S Stainless Steel in Supercritical Water: Conventional vs. Additive Manufacturing - POSTER

13:30 - 15:30

P19

NĚMCOVÁ Veronika

Research Centre Řež, Plzeň, Czech Republic, EU

Optimization of Cold Spray Deposition Parameters for Porosity Reduction of Ti 6Al 4V Coatings - POSTER

13:30 - 15:30

P20

RUPERT Robert

COMTES FHT a.s., Dobřany, Czech Republic, EU

Comparison and Optimization of Powder- and Wire-Based Direct Energy Deposited Nitinol for Thermally Activated Actuators - POSTER

13:30 - 15:30

P21

RŮŽIČKA Jana

VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU

Life Cycle Analysis and Material Flow of W-Ni-Co Systems - POSTER

13:30 - 15:30

P22

SALVETR Pavel

COMTES FHT a.s., Dobřany, Czech Republic, EU

Carbide-Reinforced NiTi Composites Produced by Direct Energy Deposition: Microstructure, Hardness and Wear Resistance - POSTER

13:30 - 15:30

P23

SÓJKA Radosław

Kielce University of Technology, Kielce, Poland, EU

Influence of Drilling Parameters Using the Dcn 120-060-16a-5d Indexable Drill on Hole Quality in C45 Steel - POSTER

13:30 - 15:30

P24

ŠINDLER Matyáš

ÚJV Řež, a. s., Husinec, Czech Republic, EU

Experimental Evaluation of Degradation in Irradiated Materials for Long-Term Operation of Nuclear Power Plants - POSTER

13:30 - 15:30

P25

UHLÍK Matouš

COMTES FHT a.s., Dobřany, Czech Republic, EU

Miniaturized Testing of Material Interfaces for Advanced Material Modelling - POSTER

13:30 - 15:30

P26

VARLIK Ertugrul

Alexander Dubček University of Trenčín, Trenčín, Slovakia, EU

Digital Light Processing of KNN-Based Piezoceramics and Magnetic Glasses toward Multifunctional Smart Structures - POSTER

13:30 - 15:30

P27

VÁVROVCOVÁ Zuzana

ÚJV Řež, a.s., Husinec Řež, Czech Republic, EU

Metallographic Characterization of Inconel Alloys in Conventionally and Additively Manufactured Conditions - POSTER

13:30 - 15:30

P28

VESELÁ Jana

Research Centre Rez, Pilsen, Czech Republic, EU

Ut Results of A508 Steel Prisms Printed by Ded Technology - POSTER

13:30 - 15:30

P29

WOJTECZKO Agnieszka

AGH University of Krakow, Kraków, Poland, EU

Mechanical Performance of Bioactive Ceramic Composites for Bone Regeneration - POSTER

13:30 - 15:30

P30

ZIĄBKA Magdalena

AGH University of Krakow, Kraków, Poland, EU

ZrO₂-Based Ceramic Composites - Physicochemical and Biological Properties - POSTER

13:30 - 15:30

P31

ZIARKOWSKI Piotr

Kielce University of Technology, Kielce, Poland, EU

Dynamic State Diagnostics of EN-GJL 250 Gray Cast Iron Face Milling Using Laser Interferometry - POSTER

13:30 - 15:30

P32

ZOUFALÝ Ondřej

Czech Technical University in Prague, Prague, Czech Republic, EU

Design of Lattice-Based Piezoceramic Actuators for Additive Manufacturing - POSTER

13:30 - 15:30

P33

ŠPIRK Stanislav

University of West Bohemia, Pilsen, Czech Republic, EU

Numerical Investigation of the Impact Response and Energy Absorption of an Additively Manufactured TWIP Steel Gyroid Structure - POSTER

POSTEROVÁ SEKCE

Datum: 9.9.2026

Hlavní sponzor

Sponzoři

Organizátoři

Partner

Mediální partneři