SESSION B - SURFACE ENGINEERING & MATERIALS
Date: September 8, 2026
Non-exhaust particulate emissions from braking systems represent a rapidly growing source of air pollution and are becoming a critical challenge in view of upcoming Euro 7 regulations. This work focuses on the development and evaluation of wear-resistant coatings for gray cast iron brake components aimed at reducing wear and particle emissions while maintaining stable frictional performance. Coatings were deposited using High Velocity Oxygen Fuel (HVOF), Cold Spray (CS), and High-Speed Laser Metal Deposition (HSLMD) technologies. The deposition procedures were optimized to achieve crack-free coatings without the use of bond coats and without conventional grit-blasting surface preparation, thereby improving process efficiency and reducing production time. Selected mechanical and wear-related properties of the coatings were experimentally evaluated and compared. The results demonstrate the potential of advanced coating technologies as industrially viable solutions for next-generation low-emission braking systems.
Molybdenum (Mo) and its composites are excellent candidates for extreme high-temperature structural applications produced via additive manufacturing; however, challenges in obtaining Mo-based composite powders limit wider implementation of this technology. This research establishes versatile and scalable powder manufacturing approaches based on chemical synthesis and mechanical alloying methods, providing a pathway for fabricating high-performance 3D-printed Mo-composite components. As a chemical engineering strategy, a combination of spray drying and hydrogen reduction was employed to synthesize engineered Mo-based composite powders tailored for advanced manufacturing. Precursor solutions and suspensions were modified to introduce structural reinforcements. For oxide dispersion-strengthened (ODS) systems, introducing La2O3 and ZrO2 particles into a water-based or alcohol-based ammonium heptamolybdate tetrahydrate (AHT) solution significantly impacted the thermal reduction kinetics and final powder morphology, with an alcohol-based suspension achieving superior phase dispersion over purely aqueous variants. Concurrently, introducing silicon (Si) particles into water-based AHT solution yielded highly spherical Mo-Si composite powders featuring unique hollow-shell architectures. To bridge powder synthesis with structural fabrication, these customized powders were processed into complex 3D porous lattices via direct ink writing (DIW) technology. As a mechanical alloying strategy, high-energy ball milling of Mo and Si powders was used to optimize ink rheology, drastically reducing intra-filament porosity and enabling low-temperature sintering densification. Under mechanical evaluation, the DIW-printed lattices displayed exceptional performance. While high silicide additions prompted brittle macroscopic failures, low-silicon variants, yielding localized Mo3Si intermetallic phase, achieved an optimal structural balance, demonstrating high monotonic compressive strength alongside robust cyclic fatigue resistance without structural degradation.
Hot Metal Gas Forming (HMGF) is a technology to inflate tubular semi-finished products at high temperature. When used for steel tube, it means inflation in the austenitic state into the cavity tool with controllable surface temperature. Contact with the tool wall defines the shape of the final product as well as cools down the material rapidly. This provides conditions for martensite or bainite formation. It is suitable for quenching and partitioning (QP) treatment to be integrated into HMGF process. Due to previous processing of the tubular components, e.g. by roll forming or U-O bending, plastic strains are introduced. These influence the properties during HGMF.
The cooling path of the material in the tool depends on the tool wall temperature and thermal conductivity. Furthermore, it highly depends on the quality of contact with the wall. Therefore, it is necessary to understand, what microstructure (and thus properties) are produced by various cooling paths.
This article describes microstructure development of QP steel 42SiCr after various cooling paths. These paths model cooling in a HMGF tool with different thermal conductivity of the tool wall as well as different heat transfer efficiency. The heat treatment of the specimens was carried out by the quenching dilatometer. The microstructure was examined by scanning electron microscopy and retained austenite content was measured by X-ray diffraction. The results show a range of technological parameters suitable for development of QP microstructure and tailored properties of the final product.
In this work, the in-depth residual stress distribution, the dislocation densities, and the microstructural changes within the surface layer of the 4 mm thick commercial bainitic-martensitic steel sheets were examined under various surface conditions: as-rolled, dry electropolished, ultrasonic burnished, and a combination of dry electropolishing and ultrasonic burnishing. X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) techniques were used in this investigation. The results proved that the dry electropolishing and the ultrasonic burnishing significantly reduced surface roughness but simultaneously increased the surface hardness due to the increased dislocation density. However, the ultrasonic burnishing also induced compressive residual stresses, which have been indicated to be beneficial for the fatigue durability. Finally, the surface characteristics achieved by the dry polishing and ultrasonic burnishing are compared to the as-rolled surface, and the effect of the surface treatments on the bendability and the fatigue durability is discussed.
