SESSION E - MATERIALS FOR ENERGY & EXTREME ENVIRONMENTS
Date: September 10, 2026
High-entropy and compositionally complex alloys offer an exceptionally broad design space for energy-related applications, but their performance is strongly governed by the selected manufacturing and processing route. Two complementary case studies will be presented. The first, a non-equiatomic TiVNbCr alloy, was designed and investigated as a solid-state hydrogen-storage material in atomised, cast and mechanically processed conditions, including severe plastic deformation. Particular attention was paid to the effects of phase constitution, activation conditions, powder state and deformation history on hydrogen uptake, sorption kinetics and long-term thermal stability. Gas atomisation produced a chemically homogeneous material containing two closely related BCC phases, while subsequent deformation processing and the addition of a catalytic component provided further routes for modifying and improving hydrogen-sorption behaviour. The second case study focuses on the eutectic AlCoCrFeNi2.1 alloy, produced as a 50 kg ingot for potential high-temperature structural applications. Its two-phase B2/FCC microstructure, response to heat treatment, precipitation behaviour, mechanical and creep properties, and oxidation and corrosion resistance were evaluated. Together, the two alloy systems demonstrate how processing history controls phase evolution, microstructural stability and application-relevant performance in advanced materials for the energy sector.
This study compares the thermodynamic model developed by Zepon et al. (Acta Mater. 2021) with experimentally determined hydrogen-sorption properties of an equiatomic CrNbTi alloy produced by Directed Energy Deposition (DED). The model calculates pressure-composition-temperature (PCT) diagrams of BCC alloys directly from chemical composition. For the nominal Cr₃₄Nb₃₃Ti₃₃ composition, it predicts two pressure plateaus corresponding to the α→β and β→δ transitions, together with a reversible hydrogen capacity of several wt.%.
A bulk DED sample was tested at 200 °C using a Sieverts-type volumetric apparatus. The experimental PCT isotherm confirmed the presence of two plateaus, although both occurred at substantially lower pressures than predicted for the nominal composition. This discrepancy is attributed to dendritic segregation inherent to the DED process. Nb-rich dendritic regions exhibit a more negative partial molar enthalpy of hydrogen and consequently lower plateau pressures, whereas Cr-rich grain-boundary regions enriched in oxides may form diffusion and thermodynamic barriers to hydrogen absorption. The observed behaviour therefore reflects not only the nominal alloy chemistry, but also the local compositional and structural heterogeneity introduced during additive manufacturing.
Despite the quantitative difference, the model correctly predicts the presence and sequence of both plateaus and the accessibility of the β→δ transition within the experimentally measurable pressure range at 200 °C. The results indicate that prediction accuracy for DED-fabricated samples could be improved by replacing the nominal alloy composition with the experimentally determined composition of the dendritic regions as the model input. Nevertheless, uncertainties associated with the EDX quantification of local chemical composition must be considered.
In this work, we investigate the structure and basic mechanical properties of a bimetallic system of high industrial relevance, namely high-strength steels clad with stainless steel. The material was produced by explosion welding, a process capable of joining a wide range of similar and dissimilar metals. Bimetals intended for industrial applications are designed to combine the advantages of two dissimilar materials: a base material (high-strength steel) that fulfils the mechanical requirements, and a cladding material (stainless steel) that provides an H₂ barrier and resistance to hydrogen embrittlement. Such bimetallic combinations could be used for pipes and tubular components to safely and efficiently store and transport H₂, particularly in stationary and potentially mobile applications involving high-pressure gaseous hydrogen (300-700 bar).
After cladding, these bimetals should be heat-treated to relieve residual stresses in both materials. The selected heat-treatment regimes are evaluated by comparing their microstructural features and basic mechanical properties. Microstructural analysis of both monolithic materials and clad bimetals is performed using light microscopy and scanning electron microscopy, with local EDS analysis. The comparison of the heat-treated specimens is complemented by basic mechanical characterisation, including hardness profiles/maps and mini-tensile tests. Because the final product consists of two different materials, the heat-treatment regimes must be selected in a balanced way so that they are suitable for both constituents. Appropriate heat treatments will therefore be applied to achieve mechanical properties compatible with the intended manufacturing processes.
This study presents a validated method for manufacturing high-strength tubular components from ultra-high-strength steel (UHSS) using U-O bending and roll forming processes. Closed profiles are created by high-frequency induction HFI welding. The primary goal was to produce geometrically accurate, semi-finished tubes suitable for subsequent tailoring of properties and further 3D bending. A synergistic approach combining non-linear Finite Element Analysis (FEA) with high-resolution optical metrology was employed to establish a reliable digital twin and define a robust process window.
The methodology was developed for 1.41 mm thick 22MnB5 UHSS. Preliminary investigations were carried for the quenching and partitioning steel (QP) 42SiCr. A two-step U-O bending process was designed, followed by a multi-stand roll forming process based on a specifically engineered "flower pattern" adhering to the Constant Arc Length (CAL) principle. Simufact Forming 2025.2 was used for all simulations, with a focus on capturing transient dynamics in roll forming and spring-back in U-O bending. A Design of Experiments (DOE) approach was applied to optimize key process parameters, including tool stroke, friction coefficient, and roll gap settings.
Experimental validation was conducted using custom-manufactured tools. U-O bending was performed on a bench press, while roll forming was carried out on an adapted mill with 8 active and 7 passive stands. The final geometries were scanned using a Zeiss T-Scan Hawk 2 laser scanner. The results demonstrated a strong correlation between simulation and experiment. For U-O bending, the predicted edge gap (5.85 mm) was within 1 mm of the measured value (6.85 mm), and the cross-sectional diameter was predicted with an accuracy of ±0.7 mm. For roll forming, the predicted edge gap (10 mm) closely matched the measured value (9.29 mm), and the roundness was within the required tolerance. The simulation successfully captured critical defects like end flare and longitudinal bow. Good weld quality in HFI welding was obtained for different parameter combinations of squeeze pressure and welding power.
This work successfully established a validated, scalable process for producing high-quality semi-finished tubes from UHSS, providing a solid foundation for downstream processes. The integrated simulation-experiment approach ensures high process reliability and is directly transferable to industrial applications.
