List of Abstracts 2024: SESSION D - MATERIALS FOR SUSTAINABLE ENERGY

Hydrogen embrittlement susceptibility (HES) and morphologies of hydrogen-related fracture for ferrite-martensitic dual-phase (DP)　steel sheets and transformation-induced plasticity (TRIP) steel sheets with the tensile strength of 1180 MPa class were investigated. HES was evaluated with fracture displacement obtained by three-point bending test at a constant displacement speed. Fracture morphologies were observed using a field emission scanning electron microscope. Specimens were electrochemically precharged with three different hydrogen charging conditions and then three-point bending tests were carried out simultaneously with hydrogen charging under the same conditions as the precharging. The result indicated that HES for both kinds of steel sheets markedly increased with increasing the hydrogen content. The fracture displacements were different between the DP and TRIP steel, indicating that the HES varied based on the microstructures. The quasi-cleavage (QC) fracture was observed on the compression side and tension side for the DP steel. The area of QC fracture surface on the compression side for the DP steel increased with increasing hydrogen content. Whereas, for the TRIP steel, QC fracture was observed in the whole area of the fracture surface regardless of hydrogen content, unlike the case of DP steel. These findings indicate that differences in the crack initiation sites and propagation paths probably cause the difference in HES and fracture morphologies.

The tensile speed dependence of crack initiation and propagation behavior in hydrogen embrittlement fracture was investigated for a tempered martensitic steel with plate-like carbides on prior austenite () grain boundaries. Notched specimens with a stress concentration factor of 2.8 charged with hydrogen of 0.2 mass ppm were tensile tested at tensile speeds of 0.001 and 0.1 mm/min. Fractured surfaces and specimen sides in which the internal crack propagation was arrested by unloaded immediately upon reaching the maximum stress in tensile tests were observed using a scanning electron microscope. At 0.001 mm/min, intergranular (IG) fracture was dominant at the notch tip on the fracture surface. A crack initiation and propagation were observed in and on the prior γ grains at the notch tip, respectively. At a site away from the notch tip, discontinuous crack initiation and propagation on grain boundaries were observed. In contrast, at 0.1 mm/min, quasi-cleavage (QC) fracture was dominant at the notch tip on the fracture surface. A crack initiated and propagated only in the prior γ grains at the notch tip. These findings indicate that even with the same hydrogen content, at lower tensile speeds, there is an increase in the hydrogen concentration on the prior γ grain boundaries, leading to decohesion of prior γ grain boundaries. In contrast, at higher tensile speeds, the involvement of plastic deformation may be significant. Therefore, the mechanism of crack initiation and propagation in hydrogen embrittlement fracture probably depends on tensile speeds.

The effects of grain boundary characteristics and grain sizes on crack propagation of hydrogen embrittlement were investigated for pure iron. Specimens with different grain boundary characters such as the low- and high-angle grain boundaries and different grain sizes were charged with hydrogen and subjected to tensile testing at a tensile rate of 0.01 mm/min. The fracture modes were observed using a field emission scanning electron microscope (FE-SEM). As a result, intergranular (IG) fracture was observed in the fine grain area and cleavage fracture was observed in the coarse grain area. In order to characterize the crystallography of hydrogen embrittlement cracks, the grain boundary character was analyzed using electron backscatter diffraction patterns (EBSD). The results revealed that the secondary cracks originated and propagated on the high-angle grain boundaries in the fine grain area. Whereas, the fracture surface was parallel to {001} cleavage plane in the coarse grain area. In addition, the specimens were strained plastically to determine the effect of dislocations on hydrogen embrittlement cracks. The IG fracture appeared in the fine grain area, while the QC fracture parallel to {011} slip plane appeared in the coarse grain area. The location of the secondary crack and the effect of dislocations suggest that the binding energies between hydrogen and lattice defects are related to crack propagation passes.

The hydrogen-enhanced strain-induced lattice defects formed during the incubation period leading to hydrogen embrittlement fracture of iron have been attempted to clarify their contribution by quantitative evaluation using low-temperature thermal desorption spectroscopy (L-TDS), which can be heated from －200 ºC. A tensile test was conducted in the solutions with various concentrations of ammonium thiocyanate as a catalyst poison. The cathodic electrolysis was employed to establish conditions for low and high hydrogen contents at fracture. The fracture elongation of the hydrogen-charged specimens was lower than that of the hydrogen-free specimens, but the ratio was the same regardless of the hydrogen contents. In contrast, the flow stress during the deformation process increased with increasing hydrogen content. Specimens were prepared under the same hydrogen charging conditions and unloaded within a uniform elongation range. Hydrogen as a probe for detecting lattice defects using L-TDS was re-charged under equilibrium conditions with dislocation cores and strain fields around the cores and vacancies in the specimens. The formation of vacancy-type defects was promoted in the presence of hydrogen during plastic deformation, and the promotion rate was similar regardless of the hydrogen content. It was suggested that the concentration of hydrogen-enhanced strain-induced vacancies may be involved in the decrease in ductility due to hydrogen, and its hydrogen occupancy rate on dislocations may be involved in the increase in flow stress.

The effects of aging treatments on the annihilation and accumulation behavior of hydrogen-enhanced strain-induced vacancies (HESIVs) formed in tempered martensitic steel were investigated. The vacancies were formed by applying plastic deformation in the presence of hydrogen. The tracer hydrogen content and peak temperature under various aging treatment conditions were measured using low-temperature thermal desorption spectroscopy (L-TDS). Aging treatments were performed in the absence and presence of hydrogen at 30 ℃ for 0, 2, 5, and 9 d. The spectra measured by L-TDS were divided into two peaks by using Gaussian curves: Peak 1H corresponding to hydrogen desorption from dislocations and Peak 2H corresponding to hydrogen desorption from vacancies. The amount of Peak 2H, i.e., the amount of vacancies decreased and the peak temperature of Peak 2H, i.e., clustered vacancy size increased with increasing aging time. The change in the amount and the peak temperature of Peak 2H was smaller than that in previous studies for pure iron. Furthermore, the change was greater for aging in the absence of hydrogen than for aging in the presence of hydrogen. Therefore, the impurities in the steel such as solid solute carbon and hydrogen probably stabilize vacancies, decrease the diffusion coefficient of vacancies, and then partially suppress the annihilation and accumulation of vacancies.